Welcome To Our Mining Equipment Production Base!
CMU Block Wall Leakage? Our Polyurethane Grout Has You …

The biggest advantage to the curtain grouting method is that no expensive excavation is necessary on the positive side of the wall. Grout Curtains can be installed behind the wall whether or not a waterproofi ng membrane was installed during initial construction. Installers can drill through the mortar joint from the negative side and pump grout with low pressure through packers into the voids ...

Read More
Polyurethane Crack Sealant Grout Material Classification ...

Drilling is usually done staggered at a 45 degree angle. The intersection point of the borehole and the crack in the structure is about 1/3 of the thickness (wall thickness) from the water side. Under these conditions, the appropriate pressure is used to inject the non-expanding polyurethane grout, which can achieve the best long-term leak stop ...

Read More
crack injection, waterstop injection, chemical grouts ...

Water activated, hydro-active, polyurethane two component water-stop injection foam in Cartridges expands up to 30-40 times. Used to stop water, to fill voids, hairline cracks and for soil stabilization. Also available in bulk packaging. Phthalate free (dbp free) SealBoss ® 1500 Hot Shot WaterStopFoam

Read More
DIY Repair Leaking Basement Wall Crack | 10 ft. Starter Kit

Cracks are completely filled from front-to-back and top-to-bottom to form a flexible and watertight repair. Provides the ultimate stop gap against water and soil gases, such as radon. The proven low pressure crack injection process is used by professional contractors and do-it-yourselfers to successfully repair basement wall cracks.

Read More
Fosroc Nitofi ll PU150 constructive solutions

out with water. This is only required if the crack is dry and there is no moisture available for the reaction of polyurethane resin. The resin can be pumped by means of a single component in injection pump that is equipped for high pressure. Following the injection, the pump must be thoroughly cleaned with Fosroc Solvent 10.

Read More
Polyurethane Crack Repair | Polyurethane Foam & PU Injection

Using polyurethane foam injection, we can seal cracks and eliminate water and air leaks from foundation walls and provide an effective permanent solution to leaking cracks. Polyurethane foam injection is ideal for filling wide cracks on concrete, masonry surfaces. The polyurethane foams can also be used to fill voids and sealing around pipes.

Read More
Crack Injection for Concrete Basement Walls - Concrete Network

The whole purpose is to fill the crack, from front to back, with epoxy or polyurethane. "For basement walls, low-pressure injection is the best way to ensure that the crack is completely filled," Cole maintains. This method is effective for filling cracks 0.002 to 1 inch wide in walls up to 12 inches thick. It can also be used to fill cracks in ...

Read More
High Pressure Injection or Low Pressure Injection - conCrack

Cities and utility companies use high pressure injection almost exclusively in sewers, bridges and public buildings. High pressure crack fills use 4 or more times the volume of grout. A high pressure pump forces the liquid grout into the entire crack no matter how small the crack is. As the grout cures it produces a much finer pore structure.

Read More
Foundation Crack Sealing - AquaGuard Injection ...

It is used exclusively for stopping leaks in poured concrete foundation walls and structures. When waterstopping is required in subway tunnels and mineshafts, the cracks and rock fissures are injected with polyurethane (also referred to as grout) – so you …

Read More
Crack Injection | High-Pressure and Low-Pressure Injection

Low-pressure injection. The low-pressure injection method involves inserting a liquid at a very low pressure into a narrow crack (more than 1/16″ or 1.5 mm).. This type of injection requires some basic equipment: a caulking gun, a dual-cartridge gun or a hand-held sprayer. However, the crack injection technique requires some practice for the repair to be effective.

Read More
Concrete Crack Injection for Basement Walls

Complete crack injection kits for homeowners and waterproofing contractors. Low-pressure injection kits for an easy and professional-grade repair of cracks in poured concrete walls. No special tools for DIY kits — just a standard caulking gun. Stop or prevent water leaks through wide or hairline cracks in poured concrete foundations.

Read More
Buy Waterproofing Grouting Injection Pump Machine For ...

(BEST OFFER) US $168.00 | Buy Waterproofing Grouting Injection Pump Machine For Concrete Wall Water Leakage Crack From Merchant Kaihua Building Material Co.,Ltd Store. Enjoy Free Shipping Worldwide! Limited Time Sale Easy Return. Shop Quality & …

Read More
Wall Crack Injection in Chicagoland

A low pressure injection of polyurethane foam or epoxy is used to seal the crack from inside the basement. Concrete Cracks. Cracks in concrete caused by shrinkage are a common foundation problem. Cracks due to shrinkage are easy to detect, since they almost always extend through the full thickness of the foundation wall. Unfortunately, such ...

Read More
OKGF 50 waterproof crack sealing machine pu grouting pump

China High Pressure Injection Grouting Machine - China ... 1.The waterproof grouting machine is for crack repair. The high pressure deliver the material to the center of wall crack,the material diffuse from center to all direction.The material fast react with water and harden to plug up the crack permanently and stop the water leaking. 2.This high pressure injection machine can stop the …

Read More
Best High Pressure grouting PU epoxy Injection pump ...

High Pressure Injection Grouting Packer, make from Aluminum, it can work at 10 MPa / 1465 psi / 100 bar pressure, easy to use, easy to inject, can use at low temperatures; single component grouting, simple construction, easy to clean up. The sealing agent can be water base polyurethane, oil base polyurethane and epoxy resin.

Read More
One of the best injection grouting waterproofing in the UAE.

Lift Pit Injection is to drill holes through the walls and floor using a grid pattern and then pump water activated polyurethane chemical grout into the soil to create "curtain wall". This wall will stops the water from penetrating the area around the pit. This acts as a permanent seal. Earth Pit Injection Treatment.

Read More
ODISHA POWER GENERATION CORPORATION LIMITED …

Pressure grouting with low viscosity epoxy injection resin with the help of injection gun or similar ... manufactured recommended pressure with the help of hand operated or mechanical grouting pump. The material of injection grouting is as follows:Cement‐ as recommended by ... If water is flowing out of the cracks, or even coming out under ...

Read More
Epoxy Pressure Injection Service - Contech Services

We do epoxy pressure injection to repair cracks on your infrastructures. This is a cost-effective method to repair damaged concrete walls, columns, slabs, and piers. We are recognized as the number one Epoxy pressure injection contractor in the Western United States of America.

Read More
Injection Grouting Facts | Waterproofing Contractor Singapore

The Pressure Injection System can be used for injecting cracks, cold joints, expansion joints and for soil stabilization. The system can be used to stop gushing water, to seal minor seepage, to regain structural integrity and to waterproof and strengthen almost any concrete or masonry structure from the positive or negative side, below grade, above grade and under water.

Read More
Polyurethane Injection Systems - ECMAS Group

PU Injection To Repair Cracks After PU injection undergoes an expansion process with water, any cracks that are filled in will have a blend of water and the polymer foam type PU grout. The mixture will then expand until there is no more space to fill, successfully sealing off any path- ways the water enters through the material.

Read More
Using the SikaFix Injection Repair Kit to Fix a Crack in a ...

We used the SikaFix Injection Repair Kit to repair a crack in our basement wall. Check out this video to find out how it worked and to get some tips and tric...

Read More
Polyurethane Leaking Crack Repair | CPR Australia

Polyurethane crack injection is without a doubt the most effective leaking crack repair method in concrete. The widespread use of polyurethane, sometimes referred to as urethane or grout, for concrete crack injection is a tribute to the inherent versatility of low viscosity polyurethane injection resins for leak sealing applications.

Read More
A Practical Guide to Grouting - Parchem

Filling the Gap A Practical Guide to Grouting constructive solutions. 2 Introduction 3 1. Selecting the correct grout ... concrete foundation to stop water in the grout being absorbed into dry concrete. Subsequent moisture ... plate grout, the cracks rarely continue …

Read More
Polyurethane Grouting Technologies - IntechOpen

Polyurethane Grouting Technologies 311 3. Grouting equipment Injection of grouting material into the rock massive is performed by grouting pumps. Usually piston type pumps with electric or pneumatic drive are used. There are one component and two component pumps available. An example of a grouting pump is presented on Fig. 1 below. Figure 1.

Read More
Polyurethane grouting | Keller North America

These grouts range in density from 2 pcf to 12 pcf and expand exerting approximately 10 psi of pressure, which is enough to move a concrete slab. HB PolyLift® Polyurethane Injection is a releveling technique that raises concrete slabs and fills voids, using the regulated injection of lightweight, non-hazardous expanding polyurethane grout.

Read More
Crack Injection Pumps - Alchemy-Spetec

INJECTION GROUTING PUMPS FOR LEAK SEAL Alchemy-Spetec offers world-class Titan electric injection pumps for sealing both small and gushing leaks as well as filling voids behind and below structures. We modify these pumps to optimize them for polyurethane injection. Impact 440 Electric Injection Pump The IMPACT 440 is an advanced electric injection pump that's ideally …

Read More
Best PU injection pump High Pressure grouting Injection ...

PU injection pump High Pressure grouting Injection pumping Polyurethane Foam fill machine. ... Port Project, Top Slab, Crack, Construction Join, Shrinkage Crack, Basement hairline crack etc. water stop projects. Drill: 1 set 550W: High Pressure Hose: 1 pc 5M: Shut-off Value: 1 set: Repairing Kit: 1 set: Seal Set: ... grouting injection grouting ...

Read More
Sikadur Concrete Crack Injection Kit-432903 - The Home Depot

Sikadur Crack Weld Injection Kit is a two-component fast curing epoxy sealing system for repairing structural cracks in concrete and masonry. It conforms to ASTM C-881. It can be used for low pressure injection of cracks in structural concrete and solid masonry. Ideal for foundations, floors, columns, slabs and beams. As strong as concrete.

Read More
What is a grout pump?

Injection grouting is a process of filling the cracks, ... or grout pump by the proper use of air, water and/or flyash. ... PU grouting is a specialised technique that involves the injection of expanding polyurethane to stop any water flowing down or through cracks or to fill voids under slabs, concrete joints or behind concrete walls and ...

Read More
Sika Crack Injection Method Statement

Attention: High injection pressure can damage the structure. For maximum injection pressure see section 11.3. You can check the injection progress by monitoring injection material or water coming out of the crack or the next packer.

Read More